Attention

TYPO3 v6 has reached its end-of-life April 18th, 2017 and is not maintained by the community anymore. Looking for a stable version? Use the version switch on the top left.

There is no further ELTS support. It is strongly recommended updating your project.

Configuration of the Logging system

Instantiation of Loggers is configuration-free, as the LogManager automatically applies its configuration.

The Logger configuration is read from $GLOBALS['TYPO3_CONF_VARS']['LOG'], which contains an array reflecting the namespace and class hierarchy of your TYPO3 project.

Example:

To apply a configuration for all Loggers within the \TYPO3\CMS\Core\Cache namespace, the configuration is read from $GLOBALS['TYPO3_CONF_VARS']['LOG']['TYPO3']['CMS']['Core']['Cache']. So every logger requested for classes like \TYPO3\CMS\Core\Cache\CacheFactory, \TYPO3\CMS\Core\Cache\Backend\NullBackend, etc. will get this configuration applied. The same holds for the old pseudo-namespaces with underscore separator which are still common in extensions.

Configuring Logging for extensions works the same. If an extension uses namespaces, the syntax for the configuration is as above.

For older extensions, configuration is searched for in $GLOBALS['TYPO3_CONF_VARS']['LOG']['tx'] or $GLOBALS['TYPO3_CONF_VARS']['LOG']['Tx'] to differentiate extension classes from Core classes (as extension class names start with tx or Tx).

Writer configuration

The Log Writer configuration is read from the subkey writerConfiguration of the configuration array:

$GLOBALS['TYPO3_CONF_VARS']['LOG']['writerConfiguration'] = array(
    // configuration for ERROR level log entries
  \TYPO3\CMS\Core\Log\LogLevel::ERROR => array(
      // add a FileWriter
    'TYPO3\\CMS\\Core\\Log\\Writer\\FileWriter' => array(
        // configuration for the writer
      'logFile' => 'typo3temp/logs/error.log'
    )
  )
);

The above configuration applies to all log entries of level "ERROR" or above.

To apply a special configuration for the controllers of the examples extension, use the following configuration:

$GLOBALS['TYPO3_CONF_VARS']['LOG']['Documentation']['Examples']['Controller']['writerConfiguration'] = array(
             // configuration for WARNING severity, including all
             // levels with higher severity (ERROR, CRITICAL, EMERGENCY)
    \TYPO3\CMS\Core\Log\LogLevel::WARNING => array(
     // add a SyslogWriter
        'TYPO3\\CMS\\Core\\Log\\Writer\\SyslogWriter' => array(),
    ),
);

This overwrites the default configuration shown in the first example for classes located in the namespace \Documentation\Examples\Controller.

For extension "foo" with key "tx_foo" (not using namespaces), the configuration would be located at:

$GLOBALS['TYPO3_CONF_VARS']['LOG']['Tx']['Foo']['writerConfiguration'] = array(
     ...
);

An arbitrary number of writers can be added for every severity level (INFO, WARNING, ERROR, ...). The configuration is applied to log entries of the particular severity level plus all levels with a higher severity. Thus, a log messages created with $logger->warning() will be affected by the writerConfiguration for the log levels:

  • LogLevel::DEBUG

  • LogLevel::INFO

  • LogLevel::NOTICE

  • LogLevel::WARNING

For the above example code that means:

  • Calling $logger->warning($msg); will result in $msg being written to the computer's syslog on top of the default configuration.

  • Calling $logger->debug($msg); will result in $msg being written only to the default log file (typo3temp/logs/typo3.log).

For a list of writers shipped with the TYPO3 Core see the section about Log Writers.

Processor configuration

Similar to the writer configuration, log record processors can be configured on a per-class and per-namespace basis from the subkey processorConfiguration

$GLOBALS['TYPO3_CONF_VARS']['LOG']['Documentation']['Examples']['Controller']['processorConfiguration'] = array(
    // configuration for ERROR level log entries
  \TYPO3\CMS\Core\Log\LogLevel::ERROR => array(
      // add a MemoyUsageProcessor
    'TYPO3\\CMS\\Core\\Log\\Processor\\MemoryUsage' => array(
      'formatSize' => TRUE
    )
  )
);

For a list of processors shipped with the TYPO3 Core, see the section about Log Processors.